Exactly How to Install a Bath Tub Yourself
Exactly How to Install a Bath Tub Yourself
Blog Article
Right here in the next paragraph you'll find more amazing answers in regards to How to Install a Bathtub.
Mounting a tub isn't precisely brain surgery, yet it does call for strong plumbing, carpentry, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably tough task. If the old tub is conveniently available, the project can relocate quickly; if you have to open up a wall surface to eliminate the old bathtub as well as place the brand-new tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will need an assistant to move out the old bathtub as well as set in the brand-new one. Make sure you have actually certified on your own for the work and also are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you might require a specialist plumber to make tube links.
This post will certainly assist you install a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not need to alter the plan of your previous supply of water pipes.
Your tools and product list need to consist of the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end provides a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making sure that the washers are in place between the faucet and the sink. Protect the tap in place with the supplier offered backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap adapters. The previous type must be linked to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the tub till the spirit level reads level.
To mount faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
Turn on the water system as well as inspect all joints and brand-new pipework for leaks as well as tighten them if needed. Load the bathtub and likewise inspect the overflow outlet as well as the regular outlet for leaks.
Finally, repair the bathroom paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub ought to wait up until the bath tub has been utilized a minimum of once as this will settle it into its last placement.
Planning for the Installment
First of all, the supporting framework supplied with the bath needs to be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable tap connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, causing complications with wetness and possible leaks to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes and cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the tub with water before securing, to allow for the motion experienced when the tub is in usage. The sealant can fracture relatively very early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is a good idea to fit the floor tiles using waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that content on Tools You Need to Install a New Bathtub when doing a lookup on the search engines. Sharing is caring. You won't know, you could be helping someone out. We take joy in reading our article about Installing A Bathtub.
Book A Free Estimate
Report this page